高壓真空斷路器開關設備
2014/1/3 8:20:18 點擊:
高壓真空斷路器 開關設備介紹
“開關柜”是一種電設備,外線先進入柜內主控開關,然后進入分控開關,各分路按其需要設置。如儀表,自控,電動機磁力開關,各種交流接觸器等,有的還設高壓室與低壓室開關柜,設有高壓母線,如發電廠等,有的還設有為保主要設備的低周減載
分類
1、低壓抽出式開關柜
2、交流低壓
3、金屬鎧裝移開式開關柜
4、低壓固定分隔式開關柜
5、高壓電容器柜
6、高壓開關柜
7、中壓真空環網柜
相關標準
SJ/T 31401-1994|高壓開關柜完好要求和檢查評定方法
DL/T 791-2001|戶內交流充氣式開關柜選用導則
DL 404-1991|戶內交流高壓開關柜訂貨技術條件
DL/T 404-1997|戶內交流高壓開關柜訂貨技術條件
DL/T 539-1993|戶內交流高壓開關柜和元部件 凝露及污穢試驗技術條件
TB/T 2010-1987|27.5kV交流電氣化鐵道開關柜技術條件
DL/T 404-2005|戶內交流高壓開關柜訂貨技術條件
維護
對真空斷路器應該每年進行一次停電檢查維護,以保證正常運行。檢查應做好如下方面的工作:
a)對管子進行斷口工頻耐壓試驗,測試真空度并記錄在冊。
b)對絕緣件進行工頻耐壓試驗。
c)測試斷路器的開距、接觸行程和機械特性,并記錄在冊。
d)對各連接件的可調整處的連接螺栓、螺母等應檢查是否有松動,特別是輔助開關拐臂處的連接小螺釘,真空管動導電桿連接的鎖緊螺母等。
e)對各轉動關節處應檢查各種卡簧,銷子等是否松脫;并對各轉動、滑動部分加潤滑油膏。
f)對使用在電流大于1 600 A以上的真空斷路器,應對每極作直流電阻測試并記錄在冊。
g)如需更換管子應按產品說明書的要求進行,更換后應進行機械特性的測試和耐壓試驗。
h)年檢后和投運前應連續空載操作8~10次,一切正常方可投運。[3]
“開關柜”是一種電設備,外線先進入柜內主控開關,然后進入分控開關,各分路按其需要設置。如儀表,自控,電動機磁力開關,各種交流接觸器等,有的還設高壓室與低壓室開關柜,設有高壓母線,如發電廠等,有的還設有為保主要設備的低周減載
分類
1、低壓抽出式開關柜
2、交流低壓
3、金屬鎧裝移開式開關柜
4、低壓固定分隔式開關柜
5、高壓電容器柜
6、高壓開關柜
7、中壓真空環網柜
相關標準
SJ/T 31401-1994|高壓開關柜完好要求和檢查評定方法
DL/T 791-2001|戶內交流充氣式開關柜選用導則
DL 404-1991|戶內交流高壓開關柜訂貨技術條件
DL/T 404-1997|戶內交流高壓開關柜訂貨技術條件
DL/T 539-1993|戶內交流高壓開關柜和元部件 凝露及污穢試驗技術條件
TB/T 2010-1987|27.5kV交流電氣化鐵道開關柜技術條件
DL/T 404-2005|戶內交流高壓開關柜訂貨技術條件
維護
對真空斷路器應該每年進行一次停電檢查維護,以保證正常運行。檢查應做好如下方面的工作:
a)對管子進行斷口工頻耐壓試驗,測試真空度并記錄在冊。
b)對絕緣件進行工頻耐壓試驗。
c)測試斷路器的開距、接觸行程和機械特性,并記錄在冊。
d)對各連接件的可調整處的連接螺栓、螺母等應檢查是否有松動,特別是輔助開關拐臂處的連接小螺釘,真空管動導電桿連接的鎖緊螺母等。
e)對各轉動關節處應檢查各種卡簧,銷子等是否松脫;并對各轉動、滑動部分加潤滑油膏。
f)對使用在電流大于1 600 A以上的真空斷路器,應對每極作直流電阻測試并記錄在冊。
g)如需更換管子應按產品說明書的要求進行,更換后應進行機械特性的測試和耐壓試驗。
h)年檢后和投運前應連續空載操作8~10次,一切正常方可投運。[3]
- 上一篇:高壓真空斷路器處理對策 2014/1/4
- 下一篇:良信電器募投項目產能過剩 應收賬款壞賬率高 2013/8/22